 |  |
| |
Many ex commands that perform normal editing operations have an equivalent in vi that does the job more simply. Obviously, you will use dw or dd to delete a single word or line rather than using the delete command in ex. However, when you want to make changes that affect numerous lines, you will find the ex commands more useful. They allow you to modify large blocks of text with a single command.
These ex commands are listed below, along with abbreviations for those commands. Remember that in vi each ex command must be preceded with a colon. You can use the full command name or the abbreviation, whichever is easier to remember.
| delete | d | Delete lines. |
| move | m | Move lines. |
| copy | co | Copy lines. |
| t | Copy lines (a synonym for co). |
You can separate the different elements of an ex command with spaces, if you find the command easier to read that way. For example, you can separate line addresses, patterns, and commands in this way. You cannot, however, use a space as a separator inside a pattern or at the end of a substitute command.
For each ex editing command, you have to tell ex which line number(s) to edit. And for the ex move and copy commands, you also need to tell ex where to move or copy the text to.
You can specify line addresses in several ways:
With explicit line numbers
With symbols that help you specify line numbers relative to your current position in the file
With search patterns as addresses that identify the lines to be affected
Let's look at some examples.
You can use line numbers to explicitly define a line or range of lines. Addresses that use explicit numbers are called absolute line addresses. For example:
| :3,18d | Delete lines 3 through 18. |
| :160,224m23 | Move lines 160 through 224 to follow line 23. (Like delete and put in vi.) |
| :23,29co100 | Copy lines 23 through 29 and put after line 100. (Like yank and put in vi.) |
To make editing with line numbers easier, you can also display all line numbers on the left of the screen. The command:
:set number
or its abbreviation:
:set nu
displays line numbers. The file practice then appears:
1 With a screen editor 2 you can scroll the page, 3 move the cursor, delete lines, 4 insert characters and more
The displayed line numbers are not saved when you write a file, and they do not print if you print the file. Line numbers are displayed either until you quit the vi session or until you disable the set option:
:set nonumber
or:
:set nonu
To temporarily display the line numbers for a set of lines, you can use the # sign. For example:
:1,10#
would display the line numbers from line one to line ten.
As described in Chapter 3, you can also use the CTRL-G command to display the current line number. You can thus identify the line numbers corresponding to the start and end of a block of text by moving to the start of the block, typing CTRL-G, then moving to the end of the block and typing CTRL-G again.
Yet another way to identify line numbers is with the ex = command:
You can also use symbols for line addresses. A dot (.) stands for the current line; $ stands for the last line of the file. % stands for every line in the file; it's the same as the combination 1,$. These symbols can also be combined with absolute line addresses. For example:
In addition to an absolute line address, you can specify an address relative to the current line. The symbols + and - work like arithmetic operators. When placed before a number, these symbols add or subtract the value that follows. For example:
In fact, you don't need to type the dot (.) when you use + or -, because the current line is the assumed starting position.
Without a number following them, + and - are equivalent to +1 and -1, respectively.[16] Similarly, ++ and -- each extend the range by an additional line, and so on. The + and - can also be used with search patterns, as shown in the next section.
[16]In a relative address, you shouldn't separate the plus or minus symbol from the number that follows it. For example, +10 means "10 lines following," but + 10 means "11 lines following (1 + 10)," which is probably not what you mean (or want).
The number 0 stands for the top of the file (imaginary line 0). 0 is equivalent to 1-, and both allow you to move or copy lines to the very start of a file, before the first line of existing text. For example:
Another way that ex can address lines is by using search patterns. For example:
Note that patterns are delimited by a slash both before and after.
If you make deletions by pattern with vi and ex, there is
a difference in the way the two editors operate.
Suppose your file practice contains the lines:
| Keystrokes | Results |
|---|---|
| d/while |  The vi delete to pattern command deletes from the cursor up to the word while, but leaves the remainder of both lines. |
| :.,/while/d |  The ex command deletes the entire range of addressed lines; in this case both the current line and the line containing the pattern. All lines are deleted in their entirety. |
Sometimes, using a relative line address in a command can give you unexpected results. For example, suppose the cursor is on line 1, and you want to print line 100 plus the five lines below it. If you type:
:100,+5 p
you'll get an error message saying, "First address exceeds second." The reason the command fails is that the second address is calculated relative to the current cursor position (line 1), so your command is really saying this:
:100,6 p
What you need is some way to tell the command to think of line 100 as the "current line," even though the cursor is on line 1.
ex provides such a way. When you use a semicolon instead of a comma, the first line address is recalculated as the current line. For example, the command:
:100;+5 p
prints the desired lines. The +5 is now calculated relative to line 100. A semicolon is useful with search patterns as well as absolute addresses. For example, to print the next line containing pattern, plus the 10 lines that follow it, enter the command:
:/pattern/;+10 p
You already know how to use / (slash) in vi to search for patterns of characters in your files. ex has a global command, g, that lets you search for a pattern and display all lines containing the pattern when it finds them. The command :g! does the opposite of :g. Use :g! (or its synonym :v) to search for all lines that do not contain pattern.
You can use the global command on all lines in the file, or you can use line addresses to limit a global search to specified lines or to a range of lines.
As you might expect, g can also be used for global replacements. We'll talk about that in Chapter 6.
You don't always need to type a colon to begin a new ex command. In ex, the vertical bar (|) is a command separator, allowing you to combine multiple commands from the same ex prompt (in much the same way that a semicolon separates multiple commands at the UNIX shell prompt). When you use the |, keep track of the line addresses you specify. If one command affects the order of lines in the file, the next command does its work using the new line positions. For example:
Note the use of spaces to make the commands easier to read.
|  | |
| 5. Introducing the ex Editor |  | 5.3. Saving and Exiting Files |
Copyright © 2003 O'Reilly & Associates. All rights reserved.