Difference between revisions of "Electronics"
Jump to navigation
Jump to search
imported>Tinker |
imported>Tinker |
||
| Line 200: | Line 200: | ||
*[http://dangerousprototypes.com/blog/2016/07/20/9v1kv-dcdc-converter/ 9V/1kV DC/DC converter] | *[http://dangerousprototypes.com/blog/2016/07/20/9v1kv-dcdc-converter/ 9V/1kV DC/DC converter] | ||
*[http://dangerousprototypes.com/blog/2016/08/11/a-low-voltage-disconnect-for-12-volt-lead-acid-and-lithium-batteries/ A low-voltage disconnect for 12 volt lead acid and lithium batteries] | *[http://dangerousprototypes.com/blog/2016/08/11/a-low-voltage-disconnect-for-12-volt-lead-acid-and-lithium-batteries/ A low-voltage disconnect for 12 volt lead acid and lithium batteries] | ||
| + | |||
==== YouTube ==== | ==== YouTube ==== | ||
| Line 211: | Line 212: | ||
*[https://www.youtube.com/watch?v=IrB-FPcv1Dc How to protect circuits from reversed voltage polarity!] | *[https://www.youtube.com/watch?v=IrB-FPcv1Dc How to protect circuits from reversed voltage polarity!] | ||
*[https://www.youtube.com/watch?v=BiJMsMguv-M 6 Ways to control Motors! Including with Arduino & Raspberry Pi! How To Tutorial from NYC CNC] | *[https://www.youtube.com/watch?v=BiJMsMguv-M 6 Ways to control Motors! Including with Arduino & Raspberry Pi! How To Tutorial from NYC CNC] | ||
| + | *[https://www.youtube.com/watch?v=-ZTCQAZsOs8 Salvaging Hall Effect Sensors and Neodymium Magnets - Build an RPM-meter] | ||
---- | ---- | ||
| Line 219: | Line 221: | ||
---- | ---- | ||
| − | |||
==== Instructables ==== | ==== Instructables ==== | ||
Revision as of 18:44, 18 July 2017
Contents
Current Research
Official Blog of Silicon Labs
- Make your own Printed Circuit Board (PCB)
- Control an accelerometer over I2C
- IoT Security
Resources
Resistance: 4 Band Colour Code Calculator
Capacitance: Conversion Calculator
Software
DipTrace - Schematic and PCB Design Software
Tools
- Details about ST-Link V2 Programming Unit mini STM8 STM32 Emulator Downloader M89 Top
- Details about USBasp USB ISP Programmer Adapter for ATMEL AVR S51 WIN7 VISTA AT89S51 AT89S52
- Authentic Nitecore UM20 Dual Slot Li-ion Battery Charger
- USB Voltage Current Meter Charger Doctor Tester 200mV 0-60 Degree
- AVR Parts Tester
- DSO138
...Parts...
Microcontrollers
Knowledge
- Walking the 32bit path to a blinky LED
- MicroFAT: A File System for Microcontrollers
- Microcontroller Register Manipulation
- I2C
- I2C - Learn
- I2C Tutorial
- I2C with Arduino
- I2C with ESP8266
- I2C Projects
- SPI
- Musings on writing a software USB stack
Software (IDEs)
TI
Atmel
Renesas
Espressif
STMicroelectronics
Microchip
-STS-
Single Board Computers
High Voltage
- 50,000V High Voltage Power Supply
- Tesla Coil Projects
- ZVS Drivers
Robotics
Off-Grid
- A New & Improved Charge Controller Based on the 555 Chip
- A low-voltage disconnect for 12 volt lead acid and lithium batteries
- ARDUINO MPPT SOLAR CHARGE CONTROLLER (Version-3.0)
- DIY solar cell from scratch
...Projects...
Knowledge
- Current Limiting Resistor Calculator for Leds
- Wire Guage
- Kelvin (4-wire) Resistance Measurement
- James Lewis - They're JUST Capacitors
- How to : Control Speed of Motor
- Some discussion about switching with MOSFETs & a bit about using LTSpice
- How to Build Your Own Discrete 4-Bit ALU
- Build Your Own Motor Driver
- Inspecting Electronic Circuits with an Audible Circuit Probe
- The Basics Behind Constant-Current LED Drive Circuitry
- How Lithium-Metal Doubles the Energy Density of Rechargeable Batteries
- Intro to Stepper Motors
- Uses of Different Soldering Iron Tips
- From Resistors to ICs Color Codes
- Measuring Resistances Less Than 1 Ohm
Ideas
- Quick and Efficiently Wiring Your Prototype Circuit Board
- Using Transistor as a Switch
- 4-in-1 Arduino LCD Shield Kit
- 9V/1kV DC/DC converter
- A low-voltage disconnect for 12 volt lead acid and lithium batteries
YouTube
- #237: 4 Wire Resistance Measurement | Kelvin connection
- 4 wire kelvin resistance measurement tutorial
- Soldering Tool
- Wireless Module on Breadboard - NRF24L01+ and ESP8266
- Level Shifting Tutorial 5V-3.3V Quick and Dirty Methods
- How to Drive LEDs - Easy Constant Current Circuit
- How to protect circuits from reversed voltage polarity!
- 6 Ways to control Motors! Including with Arduino & Raspberry Pi! How To Tutorial from NYC CNC
- Salvaging Hall Effect Sensors and Neodymium Magnets - Build an RPM-meter
Reverse Engineered: 50p Electronic 555 Doorbell Kit (with schematic)
Schematic generated in Fritzing
Instructables
Caption1
- Is the best PCB etchant in every kitchen?
- Automatic Dark Detector
- How to Control a Nixie Tube with an Arduino
- Basic Electronic components
- Call Blocker / Telemarketer Stopper
- Simple Led driver/Constant-current source 20 mA
Interesting Products
-STS-
- Embedded PID Temperature Control
- Halogen Lamp Abused for Desoldering
- Finding data on old chips
- A high current power supply built around a server voltage regulator
- Direct PCB Printing with a Modified Laser Printer
